installationandoperationMODEL 315ice maker®installationandoperation
10INSTALLATIONPanel InstallationThe Model 315 will easily accommodate a door panel aslong as you follow these points.For any door handle hardware, we
Once you have located the proper position for the hard-ware, mark the holes, remove template, and drill pilotholes for mounting of the hardware. We re
Knock-out12Hinge Cover InstallationThis is to be completed after the unit is fully installed.IMPORTANT NOTE: Install the 90 degree stop prior toinstal
13INSTALLATIONInstallation Check ListThe importance of the installation of your Model 315 icemaker cannot be overemphasized. The proper installationof
14OPERATIONInitial Start Up1) Remove control box cover.2) Rotate timer shaft clockwise until the cam is in theharvest position (switch button out).3)
15OPERATIONIce ProductionThere are two distinct cycles: freeze and harvest.1 freeze cycle + 1 harvest cycle = 1 batch of 8 cubes.The freeze cycle happ
16CleaningIMPORTANT NOTE: Never keep anything in the ice stor-age bin that is not ice; objects like wine or beer bottles arenot only unsanitary, but t
17Cleaning the Ice Making System1) Open the door and turn the ice maker control knob to off.2) Scoop out all of the ice, either discard it or save it
ADJUSTMENTSThere are three items that may be adjusted: cube size, binice level and harvest time.IMPORTANT NOTE: Cube size and harvest time adjust-ment
1919ADJUSTMENTSBin Ice Level AdjustmentWhen the ice maker shuts off the ice level in the bin shouldbe even with the metal tube inside the bin. If the
InTRODUCTIONThe Sub-Zero Model 315 is a restaurant-type ice makerdesigned for home use. It produces the same high qualityclear ice that you would expe
20TROUBLESHOOTINGProblem Possible Cause Probable CorrectionThe ice maker does not operate The ice maker is unplugged Plug the ice maker inBreaker trip
21TROUBLESHOOTINGProblem Possible Cause Probable CorrectionNo ice falling in bin, but Ice may be stuck in the Check water supply – filter may be rest
22WARRANTY"Sub-Zero Protection Plan"Full 5 Year Warranty and Limited 6th Through 12th Year Warranty on the Sealed SystemFull 2 Year Warranty
SERVICEService For Your Ice MakerPlease have model and serial number available. Contactyour nearest Sub-Zero Factory Authorized Service Center inyour
Sub-Zero Freezer Company, Inc.4717 Hammersley RoadMadison, Wisconsin 53711(800) 222-7820(608) 271-2233E-mail: [email protected] 3/03®
PRE-INSTALLATIONTechnical InformationYour Sub-Zero ice maker is designed and manufacturedwith the highest regard for safety and performance. Itmeets o
4Pre-INSTALLATIONPre-Installation ConsiderationsPurer water will freeze first in the ice making molds. Thereason for this is that anything dissolved i
Pre-INSTALLATIONMoving the UnitIMPORTANT NOTE: When you move the unit into thehouse using a hand truck or dolly, position the dolly on theside of the
6INSTALLATIONPlumbingModel 315 – Gravity Drain ModelThe drain and inlet water tubes must be plumbed beforeconnecting to the ice maker. All horizontal
7INSTALLATIONPlumbingModel 315P – Pump Model1) Place ice maker in front of installed location. Adjust leg levelers to approximately correct position.2
INSTALLATIONCompleting the InstallationIMPORTANT NOTE: Turn on the water supply and checkall fittings for leaks. Make certain the electrical harness i
99IMPORTANT NOTE: There is a part, packed with the icemaker, that is required for this procedure.1) Remove the hinge cover.2) Remove the door by remov
Commentaires sur ces manuels